Watch our Installation and Operation video located here: Video
We are proud to announce the new V2 Swage It Primer Pocket Swager for the Dillon XL650 bullet press. Included is the mount, the small primer pin, and mounting hardware. Everything that you need to swage .223, or any other calibers that utilize small primers. The V2 swager has been redesigned to drastically reduce any mount movement while swaging as well as some other minor design improvements.
Whats Different Between Version 1 vs Version 2?
On our original mount there were just 2 holes drilled into the mount and it would be attached by machine screws with locking washers. For most people that worked well but some complained that the mount would loosen while swaging. On the mount we have drilled and countersunk the holes as deep as we could to do 2 things. 1. By using the largest head sized tapered screws that we could source, the surface area of the tapered head will lock down the mount far better than the original design and 2. By going as deep as we could go with the taper, we are virtually eliminating any flex from the screws. Combine that with lowering the mounting holes by 0.010, the mount will lock into place securely with very little flex or movement.
Below are the list of benefits using our swager.
- Machined from billet aerospace stainless steel.
- Heat Treated / Hardened to ensure longevity.
- Will not rust like tool steel.
- Properly re-sizing primer pockets can be achieved because our swager is frame mounted.
- You will never experience the swaging pin sticking inside the primer pocket or hitting the shell plate.
- No need to remove the rotary primer disk which means that you can swage in a matter of minutes without the need of time consuming disassembly of the primer system.
- The easiest setup available.
- Engineered to properly swage on the Dillon XL650.
- Our swager actually re-sizes the primer pocket and adds the correct fillet.
- Use your case feeder and swage over 1000 rounds per hour.
- Proudly Made In The USA!
- Our swagers are protected by U.S. Patent No. 9,494,398.
You will not be disappointed in the Swage It S650. We back our products by an unconditional lifetime warranty. If your swager breaks or wears out, just send it back to us and we will send you another free of charge!
We are not in any way affiliated with Dillon Precision.
23 Reviews Hide Reviews Show Reviews
-
Swage it S650 2
This works great and makes reloading for the 223/556 so much easier. The instructions that come with it are easy to understand and set up was easy. They also have a video that is very helpful and easy to follow for setup either way Swage it has you covered. Get it you will not be disappointed.
-
S650 Version 2 Swagger
Just finished loading 1200 rounds. This swagger saved me a lot of time by being able to size and swage in one step. Would buy again.
-
Taking out the swage at an amazing rate
I have a Dillon XL650. After cleaning and lubing 2000 x 223 REM cases, I resized and deprimed in station 1. De-swaged using the Swage It in station 2 and then in station 4 I trimmed using the Dillon RT 1500 trimmer. First time out I went through 2000 cases in 1 hour. That's 1 case every 1.8 seconds. I have the version 2 and the screws mounting the Swage It remained tight through the entire batch.
-
Does Exactly What I Expected It To Do
Fast shipping, easy setup, and works like a charm. I hand load thousands of rounds monthly (usually in one or two sessions) and until now, swaging was by far the largest bottleneck in the process. Thank you for such a well engineered product.
-
swage it for 650 works great
I saw Swage it on you tube and purchased it. It installed just like the instructions indicated and works like a charm. You don't have to push excessively hard to get the job done. ran thru 3000+ cases with it so far and everything is fine.
-
Excellent Product
Great communication and very fast shipping for this excellent swager. If you shoot Lake City or other Military brass, and have allot of it then this is the swager you need. Set up time on my Dillon XL650 was about 10 minutes. The swager operated perfectly and as described in the promo video. First run on my Dillon swaged 600 cases in 40 minutes. I highly recommend this product. Titan Armament
-
Easily wagged 2500 cases
I bought this to swage a bucket of 5.56 cases I have been saving for loading. I was tired of the old competitor. I used the XL650n with the case feeder. This made things fast and easy. The only thing I wish this was able to do was quick release for swithching from swaging to loading. But, no matter this unit is awesome.
-
Good Quality
Just received this item a few days ago when I received an email asking for a review. Seems like a good quality tool. I did attach it to my press. The tool is easy to install and pretty much aligns itself. Ran some factory brass through it just to try. Haven't tried it on military brass but it looks like it will work.
-
A Must for the Reloader
Most of all my brass is 5.56 and many have been crimped. After using the Dillion Swager for years I'm so glad Swagit was invented. Yes, if I know what I know now I would have purchased a Dillon 1050 but I'm living with my 650. Using my Mark 7 Autoloader with the Swagit is a perfect combination, love it, glad I found it.
