Loading... Please wait...
Hover over image to zoom
Swage It S650 Version 2 Combo
Product Description
|
Watch our Installation and Operation video located here: Video
We are proud to announce the new V2 Swage It Primer Pocket Swager for the Dillon XL650 bullet press. Included is the mount, the small primer pin, and mounting hardware. Everything that you need to swage .223, .308, or any other calibers that utilize small or large primers. The V2 swager has been redesigned to drastically reduce any mount movement while swaging as well as some other minor design improvements.
Whats Different Between Version 1 vs Version 2?
On our original mount there were just 2 holes drilled into the mount and it would be attached by machine screws with locking washers. For most people that worked well but some complained that the mount would loosen while swaging. On the mount we have drilled and countersunk the holes as deep as we could to do 2 things. 1. By using the largest head sized tapered screws that we could source, the surface area of the tapered head will lock down the mount far better than the original design and 2. By going as deep as we could go with the taper, we are virtually eliminating any flex from the screws. Combine that with lowering the mounting holes by 0.010, the mount will lock into place securely with very little flex or movement. Below are the list of benefits using our swager.
You will not be disappointed in the Swage It S650. We back our products by an unconditional lifetime warranty. If your swager breaks or wears out, just send it back to us and we will send you another free of charge! We are not in any way affiliated with Dillon Precision. |
Find Similar Products by Category
Product Reviews
Showing reviews 1-10 of 30 | Next
-
time Saving Swage
Posted by Unknown on Sep 15th 2018
Works as advertised. Swages without removing any brass.
-
Much Needed for Military Brass
Posted by Steve on Aug 28th 2018
This is one of the best accessories for the 650 that I have come across. It mounts to the machine easily is very well made and fit perfectly. Being able to size an swage the crimped primers in one stroke not only makes processing easy but is the fastest way to process brass. Wish I would have bought it earlier. Bravo for the design and fast service.
-
gets the job done!!!!
Posted by dust45@aol.com on Apr 30th 2018
The product works great. I have only Swaged and reprimed about 200 223 and did not have a problem with one primer seating properly. I like this product so much I am selling my Dillon super swage 600. The shipping took longer than expected, exactly 7 days to be exact. Other than that no complaints.
-
swage it XL650
Posted by Ted on Apr 24th 2018
Shipping to Canada was quick
very easy to mount on my press
now i de-prime , size and swage
on extra toolhead in one step on the Dillon press
very happy and would recommend this
-
Works as advertized
Posted by Dr. Joe Niamtu on Apr 12th 2018
Hand swagging is a pain adn time consuming. I did not realize this product was available and I randomly Googled "Swagger for DIllon 650" and bang, this product came up.
It came in 2 days and took 2 minutes to install. It is a finely machined component and is actually pretty.
When you push the Dillon handle forward (same movement as priming) you can feel the punch enter the shell. When you pull pack, it hangs a bit, bit I guess that is part of the swage. I have only used small punch and only on 223 so far. Some are easy and some require more handle pressure. I began putting a small bit of Imperial Case Lube on the punch every 8-10 rounds and that makes the task easier. Since I deprime and resize first, then steel pin tumble, I am not worried about "grease" in my primer pocket.
The company says that this is no more of a strain on the 650 than pushing the primers.
So far I like this thing, it has taken hours off of my reloading. Anxious to see what the bigger punch does with 308.
You do have to check the mounting screw tighness every so often.
-
Worked perfectly
Posted by COReloader on Apr 9th 2018
I had about 1K .223 brass mostly prepared when I ordered the Swage It. I deprimed/sized about 700 of them before the Swage It arrived. I watched the short video, installed it and went to work. I deprimed/sized and swaged 200 rounds, then removed the Swage It and loaded the rounds in an hour! The following day I removed the tool head and only swaged the brass I had prepped. I Swaged just over 700 brass in one hour. This tool is exactly what I was looking for to reduce brass prep time. No issues with depth of Swage, or primers not seating fully or looking like they were crammed in. Getting the feel of the brass as you Swage is different but easy pick up on.
-
Good quality and a great idea
Posted by Bryan Allen English on Apr 3rd 2018
I ordered it trying to incorporate swageing into my 650,it not met expectations it exceeded them,great quality product,well built and well engineered, shipping was prompt,it fine perfect and works even better
-
perfect addition to 650
Posted by Unknown on Jan 24th 2018
When reviewing my reloading efficiency I decided to break rifle processing into brass prep and reloading. I use a lot of crimped brass so my swage step needed a serious upgrade to eliminate touching every piece. This tool is the perfect addition to my bench and enabled me to process 500 30-06 cases in an hour.
-
Best swage on the market!
Posted by 4larry@bellsouth.net on Oct 22nd 2017
Wonderful tool for the 650! Makes processing brass very easy!
-
Great!
Posted by Jim Swindle on Jun 29th 2017
Fast delivery, just a couple days after I purchased them. Easy install and easy to use. Helps with 45 ACP too, I use the large primer tool, and if it doesn't 'feel' right, I know I have a small primer pocket and I eject that one out and move on. Easier than sorting by hand.
Showing reviews 1-10 of 30 | Next